Visionis FPC-5599 One Door Access Control In Swinging Door 1200lbs Maglock + Slim Outdoor Digital Touch Keypad/ Reader Standalone With Mini Controller + Wiegand 26, No Software, EM Card + PIR Kit

Description The 5599 kit is a one door 1200lbs Maglock Access Control Kit for doors that open in with request to exit PIR. This system is mainly used to give access to a certain room, office or building (depending on your application) to certain people. With the outdoor slim keypad, the VIS-3003, you can gain access through three different options. You can enter a pin code onto the keypad, use a proximity card, and/or use a proximity key tag. This keypad will allow up to 1000 users through either of the three access options. Since this is a standalone system, meaning that there is no software, it is recommended for you to keep a record of all personnel and their assigned user ID with key code, key card or key tag. On the keypad, you will notice a doorbell towards the bottom. This will allow people from the outside to ring the doorbell and notify those inside that there is someone wanting to come in. Once someone has entered a programmed code, card, or tag, the maglock will disengage and allow for entrance. The lock will then engage again and remain closed until it is unlocked by one of the three access options. The VIS-7005 exit button will allow those from within the facility to exit when they push the button. Through the outdoor keypad, you can program your delay from 0 to 99 seconds. The meaning of having a delay is setting a time until the maglock engages again. The popular applications for this kit is for offices, commercial buildings or any room that needs restricted access. The request to exit PIR included in the kit allows for the door to unlock when it senses motion within 2.4m. The VIS-MINI-CNTRL is a mini single door control panel that can work with any Wiegand 26~37 bits output reader. It uses Atmel microcontroller to assure stable performance, and it is equipped with an infrared remote control for easy operation. The VIS-MINI-CNTRL supports 1,000 users. IMPORTANT: Professional installation is recommended. This kit brings a fail-safe lock which means that the lock will release when there is no power. Many states have fire codes that require this type of locking device to be used in case of an emergency. You are able to use a battery back-up UPS device only if approved by your areas fire department fire code. For better security the VIS-MINI-CNTRL needs to be installed inside the facility in a restricted area. This device becomes the hub of this standalone application and all the credentials are being stored on the device while no information is stored on the reader itself. Additional recommendations for added security is to add the controller within an enclosure. If the keypad/card reader (entry device) is tampered with, the door will remain locked. The mini controller is the one controlling and securing your locking device. The VIS-MINI-CNTRL offers a more secure option to provide additional security to all type of standalone access control products. This PRODUCT has a 3 YEAR warranty with full access to tech support in the USA!

Kit Includes: (1) VIS-ML1200LED - 1200lb Indoor Electromagnetic Lock with LED Sensor (1) VIS-ZL1200 - L and Z Bracket for 1200lbs Electromagnetic Lock (1) VIS-3003 - Access Control Indoor + Outdoor Rated IP68 Metal Anti Vandal Digital Touch Keypad + Reader Standalone with Mini Controller, Wiegand 26, Slim Design No Software EM Cards, 1000 Users (1) VIS-MINI-CNTRL - 1 Door Controller for Access Control Systems with No Software. Up to 1,000 users (1) VIS-7005 - Indoor Ultra Thin Push + Touch To Exit Button For Door Access Control With LED Light NC COM and NO Outputs (10) VS-VIS-APROXCARD/26 - Access Control Proximity Contactless Smart Entry Card 1.8mm Thick 26 bit 125khz (10) VIS-AKEYTAG - Access Control Proximity Contactless Smart Entry Keyfob 26 bit 125khz (1) VIS-8006 - External Hardwire Doorbell for Keypad/Reader Access Control (1) IrexPlus - Rokonet Risco Request to Exit PIR motion Sensor with Internal Buzzer and Relay Timer (2) VISCP100 - 12 Volt 1AMP Power Supply Transformer Model VIS-ML1200LED: Voltage Input: 12 VDC / 24 VDC Current Draw: 12V / 500mA ; 24V / 250mA (±5%) Holding Force: Up to 1200 lbs (545 kg) Hall Effect Contact: SPDT rated 2A at 24 VDC Magnetic Contact Rating: 28 VDC, 0.2A, 5W Anti-Rust Surface Treatment: Blue Zinc Plating Operating Temperature: 0~55° C (32~131° F) Weight (Magnet): 2.5 kg (±1%) Dimensions: Magnet - (L)266x(W)67x(T)39 mm Armature - (L)185x(W)61x(T)16.5 mm Green/Red LED Indication for EM Lock Status Model No. VIS-3003: Input Voltage: DC 12V Idle current: ≤25mA Card Reading Distance: 2 - 3 cm (0.78 - 1.18 in.) Card Frequency: 125KHz for EM // 13.56MHz for MFR Card Transmission Format: Wiegand26 Keypad Transmission Format: 4bit, 8bit and Virtual card number Operating Temperature: -45°C ~ 55°C (-49°F ~ 131°F) Operating Humidity: 0%~95% Product Size: 133Lx59Wx21H (mm) - 5.23Lx2.32Wx0.82H (in.) Protection Level: IP68 - No ingress of dust; complete protection against contact (dust tight), and waterproof Model No. VIS-MINI-CNTRL: User Capacity: 1,000 Operating Voltage: 9~24V DC Idle Current: < 20mA Relay One: (NO, NC, Common) Adjustable Relay Output Time: 1~99 Seconds (5 seconds default) Lock Output Load: 2 Amp Maximum Wiegand Interface Input: Wiegand 26~37 bits Wiegand Interface Output: Wiegand 26~37 bits (for user transfer) Environment: Indoor Operating Temperature: -40°C~60°C (-40°F~140°F) Operating Humidity: 0 ~ 90%RH Physical: ABS Shell Dimensions: L65 x W54 x H19 (mm) - L2.56 x W2.13 x H0.75 (in.) Unit Weight: 40g Shipping Weight: 100g Model No. VIS-7005: Contact Rating: 3A/12-24V Output Contact: NO/NC/COM Power: 12VDC - 24VDC LED Color: Blue (Stand by Mode), Green (Active/Open Mode) Panel: 4mm (0.15in.) Thick Aluminium alloy (CNC) Suitable for Door: Hollow Door Mechanical Life: 100.000 tests Operating Temperature: -20°C~+55°C (14°F-131°F) Operating Humidity: 0-95% (relative humidity) Weight: 0.065kg Dimension Of Plate: 86L × 50W × 25H mm - 3.38L x 1.96W x 0.98H in. Model No. IrexPlus: Voltage: 12-30 Volts DC or AC Current Consumption: 8 mA standby, 25 mA (Relay+LED), 44 mA maximum (Buzzer+Relay+LED) at 12/24 VDC Relay Output: 1A @ 30 VDC or VAC, two form “C” contacts Tamper Output: 50 mA @ 30 volts DC or AC Detection System Mounting Height: 2.3m - 4.6m (7.5' - 15') Detection Range: Up to 2.4m (8') Dimensions (LxHxD): 177mm x 50mm x 45mm (7'' x 2'' x 1.8'') Weight: 0.15Kg (0.3lb) Colour: White or Black Environmental RFI Immunity: 30 V/m from 10MHz to 2GHz Operating & Storage Temperature: -20°C to 60°C (-4°F to 140°F) Model No. VS-VIS-APROXCARD/26: Proximity cards (or access cards) are hybrid technology that incorporate a simple electric circuit (proximity tag and coil) embedded in a plastic card. No battery is needed and the circuit is not removable without destroying it and the card. When the card is correctly positioned with respect to a reader a high speed RF signal passes between card and reader and unique data is transferred. This ISO standard proximity card is 1.8mm thick and can have printed material attached to the front. It is supplied with a pre-assigned unique code. Model No. VIS-AKEYTAG: Proximity contactless Smart Entry Keyfob 26 bit 125khz Range: 5cm-10cm (1.97″-3.94″) Water proof Shock proof Uses ultrasonic connection Each tag has a unique pre-assigned code (8 digit number) printed on the back Dimensions: 39mm x 35mm x 7mm (1.54″ x 1.38″ x 0.28″) Model No. VIS-8006: External hardwire doorbell for Keypad/Reader Access Control Dimensions: L87xW62xH23 mm or L3.43xW2.44xH0.90 Inches